Cablu coaxial 75 Ohm TRISET 302 B2ca clasa A+ 1,02/4,6/7,0 110 dB 500 m

Close-up of the Tri-Shield TRISET 302 Eca cable. Braid coverage 77% (aluminum) High-quality Tri-Shield TRISET 302 B2ca E1006 coaxial cable intended for both individual and collective installations. Cable with LSZH (LS0H) jacket - halogen-free insulation, used where greater safety in the event of fire is needed (tall and high-rise residential buildings, public utility buildings). In the event of a fire, these cables do not spread flame, smoke emission is very low, and the emitted gases are not corrosive. They can be successfully used in DVB-T2 digital terrestrial television and FM radio installations /DAB and multiswitch systems (terrestrial DVB-T2 and satellite DVB-S/S2). Inner conductor made of copper wire with a diameter of 1.02 mm and a triple screen (first glued Al/PET/Al foil + 77% braiding + second Al/PET foil). Key features: compliant with the class A+ standard flammability class B2ca-s1a, d1, a1 complies with the requirements of the MTBiGM regulation 1.02 mm copper core tri-shield cable - triple screen made in LSZH (LS0H) jacket - halogen-free insulation low attenuation excellent fit high shielding effectiveness - in the frequency band up to 2 GHz meets the requirement of class A++ min. 77% braid coverage The high-quality, triple-shielded coaxial cable of RG6 category has the inner conductor made of copper wire with a diameter of 1.02 mm, which ensures low loss and durability. The copper wire core does not corrode and the cable is not stiff. The TRISET 302 B2ca E1007 coaxial cable has 77% braid coverage, guaranteeing a high level of shielding and protecting the useful signal against the influence of external interference. In the case of parallel installation of many cables and long cable sections, it is recommended to use triple-screened cables. Effective screening over long distances eliminates the likelihood of so-called cable crosstalk. It consists of inducing unwanted signals in neighboring cables. This is visible on the screen by image interference - pixelation and freezing of scenes - as is the case with a weak signal or a low-quality signal. The optimally selected flexibility of the jacket allows for easy installation of the cable both in cable ducts and in installation boxes or mounting boxes. The cable is manufactured under strict quality standards, with tight tolerances. In order to secure the minimum bend radius, flush mounted installations should be done with the use of protective conduits. The Tri-Shield TRISET 302 B2ca E1007 coaxial cable meets the EN50117 standard for shielding (class A+) in the frequency band 5 - 3000 MHz. The cable has a declaration of compliance with the RoHS directive (.pdf)Declaration of conformity of technical parameters of Tri-Shield TRISET 302 B2ca E1007 (.pdf)Declaration of performance (.pdf)Detailed parameters of the Tri-Shield TRISET 302 B2ca E1007 cable (.pdf) TRISET cables are compliant with Construction Products Regulation (CPR) and EN 50575 harmonized standard that specifies reaction to fire performance requirements, test and assessment methods for cables used for the supply of electricity and for control and communication purposes, which are intended for use in construction works and subject to performance requirements on reaction to fire. The 75 Ohm TRISET 302 B2ca E1007 coaxial cable was tested by the notified body TÜV Rheinland with the number 1008 and obtained class B2ca-s1a, d1, a1 reaction to fire. Characteristics of the TRISET 302 B2ca cable coating For more on cable fire resistance classes, read The CPR Directive - the new cable order According to the EN50117 standard, coaxial cables are divided into classes: C, B, A, A+, A++, depending on the screening effectiveness. Classes of screening efficiency Class 5-30 MHz [mΩ/m] 30-1000 MHz [dB] 1-2 GHz [dB] 2-3 GHz [dB] C 50 75 65 55 B 15 75  65 55 A 5 85  75 65 A+ 2,5 95  85 75 A++ 0,9 105  95 85 Measurement results of the most important technical parameters. Coupling impedance in the frequency range 5-30 MHz and shielding of the TRISET 302 B2ca cable in the frequency range 30-3000 MHz In the frequency band up to 2 GHz, meets the requirement of class A++ Insertion loss in the 5-3000 MHz range Cable reflection loss in the frequency range 5-3000 MHz. Smith chart showing the wave impedance of the cable. Measurements taken at both ends of a 100 m section of cable. Deviations from the nominal value of 75Ω not exceeding 1% guarantee perfect impedance matching in the entire transmission path. The speed of signal propagation in a cable in the frequency range 5-1000 MHz. Tip produs Cablu coaxial Tip TRISET 302 B2ca Producător TRISET Lungime cablu m 500 Utilizare Interior Clasă cablu RG-6 Respectarea legislației naționale relevante Da Clasă CPR B2ca Proprietăți fizice Impedanță Ohm 75 Clasă ecranare A+ Impedanta de transfer TI mΩ/m < 2,5 Conductor Material Cupru Conductor Diametru mm 1,02 Dielectric spumare Fizic Dielectric Diametru mm 4,6 scut Nr. straturi 3 Prima folie legat de dielectric Da Prima folie Mate